Power System Design

Key Features

  • Concept Design
  • Cost-Design Optimization
  • Protection Scheme selection
  • Protection Scheme design
  • Protection Scheme drawings
  • Cable Sizing Calculations
  • Cable Route Design
  • Planning outline design
  • Detail design
  • 11kV, 33kV and 132kV Grid connections
  • Guidance on DNO connections
  • Equipment specification
  • Operation philosophies
  • Contingency planning
  • Preparation of cable schedules
  • Substation design and layout
  • GIS / Hybrid substation layout
  • Open terminal (AIS) substation layouts
  • Battery sizing
  • UPS sizing and configuration
  • Preparation of hazardous area drawings
  • Standard installation drawings
  • IEC 61850 architecture design.

HV and LV Power System Design Capabilities

Power system design is the process of developing the electric system design to facilitate equipment ordering and construction.  The design process can range from a simple Single Line Diagram with supporting notes up to complex packages that specify everything from main busbar ratings, CT selections, through to cable terminations.

Power system design can occur in several stages. Most commonly, it is done during a specific design stage, before main equipment is ordered and subcontracts let. However, many projects also carry out a concept design phase, to identify main equipment ratings characteristics and to help avoid any unexpected surprises in the detail design stage. In our experience, we have found that companies who skip this step, or provide only a very simple outline designs to contractors  often end up in contractual arguments and have problems on site when the interface between two key items of equipment has not been properly considered.

Some of the more common study types are explained in more detail below.


Concept Design

The design process for a power system can vary enormously depending on the complexity of the power system and the existing site configuration. At one end of the spectrum, we can provide guidance for a simple low voltage DNO connection, while at the other extreme we can design a tie-in to a complex brownfield site that has limited space and outage windows.

As part of the design approach Aurora will typically begin by estimating the total power demand, selecting appropriate voltage levels, transformer rating, earthing approach, circuit breaker ratings and fault levels. On more complex sites, we can also then help to establish the required reliability and maintenance requirements of the system, and consider whether to use single radial feeders, ring feeders, or dual radial feeders and different busbar configurations and the need for emergency power supplies.


Protection & Control Design

Protection and Control design is a particularly complex area of electrical engineering, and one that carries a high risk if mistakes are made. At Aurora we pride ourselves on our detailed knowledge of protection schemes from simple LV power distribution systems, up to complex transmission systems and large MV motors and generators.

Our approach to protection design is to consider what will be the most appropriate protection scheme for any given item of plant or system, and select the most cost effective scheme based on the amount of capital invested in key equipment and the criticality of the system. As part of the protection design we would typically consider CT sizing calculations, take decisions on whether the use of differential protection at 33kV and 11kV is justified, and the appropriate selection of some of the more sophisticated types of protection devices required for generators and large motors. Part of this design process also considers the type of control system required, the need for any power management system and the type of communication protocols such as IEC
61850, DNP, MODBUS/TCP, Profibus etc. as well as the system architecture for the control network.


Equipment Sizing & Specification

An often overlook aspect of power system design is the correct sizing and specification of equipment, and use of appropriate de-rating factors; as incorrect sizing can lead to overheating of equipment and loss of useful service life. Aurora has a wide range of established equipment specifications and data
sheet templates that can be easily adapted for most Clients’ needs.
Preparation of equipment specifications, data sheets and operating
philosophies can often seem like an arduous task, but it is vitally
important; as allowing manufacturers to provide their standard design,
can often lead to contract disputes, and expensive rework.

At Aurora we regularly undertake sizing calculations for transformers, switchgear and generators and battery sizing calculations for UPS’s. Our design process ensure that we consider all key aspects of the design requirements and any identify and correctly account for any factors that may affect the equipment rating, such as ambient air temperature, altitude and design life.


Cable Sizing Calculations

Cable Sizing calculations, is an often misunderstood design process, and it is common to find cables that are not correctly sized, for one reason or another, typically with designers forgetting to consider a cables fault rating, de-rating factors or sheath sizing.  At Aurora we regularly undertake sizing calculations for cables using the different approaches given in BS 7671, IEC 60364, 60502-2 and 60287 and sometimes even the old ERA 69-30 method. At Aurora are capable of sizing everything form LV cables up to complex 400kV transmission cables and their associated Sheath Voltage Limiters (SVLs). Our design process ensure that we consider all key aspects of the cable installation and any identify and correctly account for any factors that may affect the cables rating, as well as formally sizing it for the required short circuit carrying capacity.


Substation Design

Aurora have the capability to undertake a wide range of detailed
substation designs, from small pad-mounted LV feeder pillars, up to much
larger 400kV outdoor substations and complex GIS substation, or hybrid
substations. As part of our design we will typically prepare plan and
layout drawings, and associated civil foundation and trench details and
during the design we will consider any arc flash containment ductwork,
overhead cranes, battery room configuration and ventilation, shielding
between power and control systems, transformer pen layouts, cable
routing and bending radii, F&G detection, working and operational
areas, safety isolation and safety clearances, access for
maintainability and also operator access and egress. When considering
GIS substation design, we will liaise directly with GIS manufacturers to
ensure that the layouts and design reflect the manufacturers
requirements.


Detail Drawings

Aurora can prepare a wide range of detail design drawings to define the power system design. These documents are necessary to fully define an electrical system and allow a turnkey solution to be provided. Typical drawings that we prepare for clients are: Single line diagrams, protection diagrams, cable routing diagrams, lighting and small power layouts, earthing layouts, hazardous area drawings, wiring diagrams, schematic diagrams, architecture diagrams, block diagrams and many more types!